Journal of Manufacturing Processes - Elsevier.

View Investment Casting Research Papers on Academia.edu for free.

Researchers can use this section to access extensive informative on casting alloys, industry fact sheet, scrap metal, Metal recycling, metal types, metal finishing, metal forming processes, casting processes, Design aids, commercial foundries, home foundry, foundry equipment, technological news and issues, research papers, and much more.

Optimization of Sand Casting Process Parameter Using.

Popoola A. P. and Fayomi O. S. Accessing the performance of binders on core strength in metal casting, International Journal of the Physical Sciences Vol. 6(34), pp. 7805 -7810, 16 December, 2011.Die Casting Congress Papers. The Die Casting Congress plays a major role in the technology transfer efforts. Members may assist in reviewing papers prior to formal acceptance which not only provides input to the authors, but also provides members with new research results prior to the congress.The aim of the Journal of Manufacturing Processes (JMP) is to exchange current and future directions of manufacturing processes research, development and implementation, and to publish archival scholarly literature with a view to advancing state-of-the-art manufacturing processes and encouraging innovation for developing new and efficient processes.


In addition to original research articles, Journal of Advanced Research publishes reviews, mini-reviews, case reports, letters to the editor, and commentaries, thereby providing a forum for reports and discussions on cutting edge perspectives in science. All submitted papers are subjected to strict single blind peer reviewing process.Optimization of Sand Casting Process Parameter Using Taguchi Method in Foundry Rasik A Upadhye Department of Industrial Engineering, Shri. Ramdeobaba College of Engineering and Management, Nagpur 440013 India Dr. Ishwar P Keswani Professor, Department of Industrial Engineering, Shri. Ramdeobaba College of Engineering and Management.

Therefore, the present research was conducted to investigate the effect of stirring speed and pouring temperature on wear rate and microstructure of Al6061-Cu reinforced SiC MMC by stir casting.

Read More

Casting papers Experts in the production of high-quality casting papers since 1964, these products are used to apply leather-like patterns and patinas to the surface of synthetic materials. Suitable for use in the manufacture of a wide range of items including clothing, furniture, bags and automotive applications, the choice of patterns reproduces a wide variety of textile and leather finishes.

Read More

U.S. Department of Transportation Federal Aviation Administration 800 Independence Avenue, SW Washington, DC 20591 (866) tell-FAA ((866) 835-5322).

Read More

Abstract. Lost foam casting (LFC) is a green precision casting process categorized as a near net forming technology. Yet, despite its popularity, it still suffers from some technological problems, such as poor filling ability of the castings, coarse and non-dense microstructure, low mechanical properties for the Al and Mg LFC processes, and defective carburization for the low carbon steel LFC.

Read More

PhD thesis World is a group of professionals and subject matter experts who are engaged in delivering end to end research consulting services to PhD and Masters Scholars in Oman,Kuwait,Saudi Arabia,Uk,Jordan,UAE,Qatar.

Read More

Centrifugal and Vacuum Casting Procedures. Differences between centrifugal and vacuum casting will be explaining in the step-by-step guide below. Otherwise, these steps apply to either method. Make or buy a wax model or pattern. Check the model for any defects and repair if needed.

Read More

Iron Casting Research Institute. REFERENCE: Krause, D. E., “Gray Iron-A Unique. the design of a casting for gray iron is somewhat simpler than for any other foundry metal in that solidification shrinkage is at a minimum and for the. There have been numerous papers dealing with the subject of the correlation of Brinell hardness.

Read More

The Journal of Materials Processing Technology covers the processing techniques used in manufacturing components from metals and other materials.The journal aims to publish full research papers of original, significant and rigorous work and so to contribute to increased production efficiency and improved component performance.

Read More

The casting process was discovered probably around 3500 BC in Mesopotamia. Casting is unique manufacturing processes for a variety of reasons. Perhaps the most obvious is the array of molding and casting processes available that are capable of producing complex components in any metal, ranging in weight from less than an ounce to single parts weighing several hundred tons.

Read More

Casting Defects: Shrinkage, Sand inclusion, porosity, blow holes, cracks, cold shuts.etc Heavy rejections, stringent technical delivery condition by customers Inconsistent quality standards.

Read More